Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
build image using lindenis SDK
#1
1) i build the image using lindenis SDK
2) i flashed the lindenis board using phoenix app
3) AND no more output is seen on the uart-putty console after "Starting Kernel..."


what's wrong??

p.s.: 

uart0 log:

[156]HELLO! BOOT0 is starting!
[160]boot0 commit : 8 
[173]rsb_send_initseq: rsb clk 400Khz -> 3Mhz
[179]PMU: AXP233
[181]set pll start
[184]set pll end
[186]DRAM BOOT DRIVE INFO: V0.66
[189]DRAM CLK = 792 MHZ
[191]DRAM Type = 3 (2Big GrinDR2,3Big GrinDR3,6:LPDDR2,7:LPDDR3)
[197]DRAM ZQ value: 0x003b3bfb
[203]DRAM SIZE =1024 M
[205]Disable Auto SR
[207]dram size =1024
[211]common_mix:v1.1
[213]card no is 2
[215]sdcard 2 line count 8
[217][mmc]: mmc driver ver 2017-09-26 15:04
[222][mmc]: mmc 2 bias 00000000
[230][mmc]: ***Try MMC card 2***
[251][mmc]: MMC 5.0
[253][mmc]: HSDDR52/DDR50 8 bit
[256][mmc]: 50000000 Hz
[258][mmc]: 7393 MB
[260][mmc]: ***SD/MMC 2 init OK!!!***
[378]Loading boot-pkg Succeed(index=0).
[382]Entry_name        = scp
[390]Entry_name        = u-boot
[414]Entry_name        = soc-cfg
[417]Entry_name        = dtb
[422]Ready to disable icache.
[425]0xffffffff 0xffffffff
[427]0xff16ffff 0xffffffff
[430]0xff0f16ff 0xffffffff
[433]0xffffffff 0xffffffff
[435]0xffffffff 0xffffffff
[438]0xffffffff 0xffffffff
[441]Jump to secend Boot.


U-Boot 2014.07-g4074e47-dirty (Jul 30 2019 - 00:39:29) Allwinner Technology 

uboot commit : 4074e471bd50a35ea591dfb87bb5d086f7df3545
 
secure enable bit: 0
normal mode: with secure monitor
[0.445]rsb init by cpux
[0.445]rsb_send_initseq: rsb clk 400Khz -> 3Mhz
[0.446]pmbus:   ready
[0.448]PMU: AXP233
[0.450]PMU: AXP233 found
[0.453]bat_vol=724, ratio=-1
set pa_bias(0) bias:3300
set pd_bias(2) bias:3300
set pe_bias(3) bias:2800
set pf_bias(4) bias:3300
set pg_bias(5) bias:1800
set pi_bias(6) bias:1800
set pj_bias(7) bias:2800
set vcc_bias(8) bias:3300
[0.473]set power on vol to default
[0.476]dcdc1_vol = 3300, onoff=1
[0.479]dcdc2_vol = 900, onoff=1
[0.482]aldo1_vol = 3300, onoff=1
[0.485]aldo2_vol = 3300, onoff=1
[0.488]dldo2_vol = 900, onoff=0
[0.491]eldo1_vol = 1800, onoff=1
[0.494]eldo2_vol = 3300, onoff=1
[0.497]eldo3_vol = 1800, onoff=1
[0.500]dc1sw_vol = 3300, onoff=1
[0.502]find power_sply to end
[0.506]PMU: cpux 1008 Mhz,AXI=336 Mhz
PLL6=600 Mhz,AHB1=200 Mhz, APB1=24Mhz MBus=400Mhz
DRAM:  1 GiB
[0.516]fdt addr: 0x7abc9d68
[0.517]gd->fdt_size: 0x1b080
Relocation Offset is: 35d28000
gic: normal mode
[0.658][key recovery] no use
workmode = 0,storage type = 2
[0.658]MMC: 2
[0.658][mmc]: mmc driver ver 2017-11-08 20:31:00
[0.661][mmc]: get sdc_ex_dly_used 2, use auto tuning sdly
SUNXI SD/MMC: 2
[0.669][mmc]: media type 0x8000000
[0.669][mmc]: Try MMC card 2
[0.689][mmc]: mmc don't support HS400
[0.695][mmc]: host caps: 0x6f
[0.705][mmc]: MID 000088 PSN e0043124
[0.705][mmc]: PNM NCard  -- 0x4e-43-61-72-64
[0.705][mmc]: PRV 4.3
[0.705][mmc]: MDT m-1 y-2017
[0.705][mmc]: MMC v5.0
[0.705][mmc]: bus_width      : 8 bit
[0.705][mmc]: user capacity  : 7393 MB
[0.705][mmc]: SD/MMC 2 init OK!!!
[0.709][mmc]: Best spd md: 2-HSDDR52/DDR50, freq: 2-50000000
[0.721][mmc]: EOL Info(Rev blks): Normal
[0.721][mmc]: Wear out(type A): [0.721][mmc]: 0%-10% life time used
[0.721][mmc]: Wear out(type B): [0.724][mmc]: 0%-10% life time used
[0.727][mmc]: End mmc_init_boot
[0.730]sunxi flash init ok
used mbr [0], count = 4
[0.735]try to burn key
[0.737]display init start
drv_disp_init
init_clocks: finish init_clocks.
pwm_request: reg = 0x300a000. pwm = 0.
request pwm success, pwm = 0.
drv_disp_init finish
[0.764]boot_disp.output_disp=0
[0.764]boot_disp.output_type=0
boot_disp.output_mode=0
[0.764]boot_disp.auto_hpd=0
[0.767]test_disp.test_used=0
[0.767]disp0 device type(0) enable , in NormalMode
[0.769]display init end
--------fastboot partitions--------
-total partitions:4-
-name-        -start-       -size-      
boot-res    : 1000000       2000000     
env         : 3000000       20000       
boot        : 3020000       1400000     
UDISK       : 4420000       0           
-----------------------------------
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_mmc
no misc partition is found
[0.806]to be run cmd=run setargs_mmc boot_normal
read mac from efuse failed
read item0 copy0
Item0 (Map) magic is bad
the secure storage item0 copy0 is bad
read item0 copy1
Item0 (Map) magic is bad
the secure storage item0 copy0 == copy1, the data is good
the secure storage map is empty
no item name rootwait in the map
sunxi storage read fail
no item name fsck.repair in the map
sunxi storage read fail
no item name mac in the map
sunxi storage read fail
no item name wifi_mac in the map
sunxi storage read fail
check user data form private
the private part isn't exist
[0.858][mmc]: hsddr 2-50000000
[0.860][mmc]: get max-frequency ok 50000000 Hz
[0.864][mmc]: 1 1 0: 1 1 0
[0.866][mmc]: no mmc-hs400-1_8v!
[0.869][mmc]: no mmc-hs200-1_8v!
[0.876]update dtb dram start
[0.877]update dtb dram  end
PowerBus = 2( 2:vBus 3:acBus other: not exist)
(*) no battery exist
sunxi_bmp_logo_display
reading bootlogo.bmp
161660 bytes read in 4 ms (38.5 MiB/s)
[0.891]bmp file buffer: 0x40000000, bmp_info.buffer: 46400000
[0.898]fetch script data boot_disp.output_full fail
[0.901]screen_id =0, screen_width =0, screen_height =0
[0.906]frame buffer address 46400036
[0.910]inter uboot shell
Hit any key to stop autoboot:  1  0 
[1.914]read partition: boot or recovery
boota: bad boot image magic, maybe not a boot.img?
try to read partition(boot) all
[2.152]sunxi flash read :offset 3020000, 20971520 bytes OK
cmdline: mix=0x1000@0x7bd31000
mbr_partition: mbr=0x3e0
## Booting kernel from Legacy Image at 45000000 ...
   Image Name:   Linux-4.4.55+
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3280928 Bytes = 3.1 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Loading Kernel Image ... OK
(*) cmd line = earlyprintk=sunxi-uart,0x05000c00 initcall_debug=0 console=ttyS0,115200 loglevel=8 rootwait=1 root=/dev/mmcblk0p1 fsck.repair=yes init=/init partitions=boot-res@mmcblk0p2:env@mmcblk0p5:boot@mmcblk0p6:UDISK@mmcblk0p1 cma=384M vmalloc=480M mac_addr= wifi_mac= mix=0x1000@0x7bd31000 mbr=0x3e0   reserving fdt memory region: addr=40000000 size=1000
   reserving fdt memory region: addr=40020000 size=800
   reserving fdt memory region: addr=48100000 size=4000
   reserving fdt memory region: addr=48104000 size=1000
   reserving fdt memory region: addr=48105000 size=1000
   Using Device Tree in place at 44000000, end 4401e07f
(*) krn = e1a00000
[2.222]para err in disp_ioctl, cmd = 0xa,screen id = 1
[2.225][mmc]: mmc exit start
[2.244][mmc]: mmc 2 exit ok

Starting kernel ...
Reply
#2
Dear sir, have you tried to use our prebuilt image on ftp server to make sure your hardware works well ?
You can download the image following this guide:
http://wiki.lindeni.org/index.php/Main_P..._the_image
Powered by Given @ Lindenis  Big Grin
Reply
#3
"..have you tried to use our prebuilt image..." yes, it's ok. i see even the desktop via hdmi

yesterday, i rebuild the image again(delete kernel directory and run 'repo sync' console command ). flashed it and got the log below:

....
....
....
[2.272][mmc]: mmc exit start
[2.291][mmc]: mmc 2 exit ok

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.55+ (aa@aa) (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05) ) #1 SMP PREEMPT Sun Aug 11 19:43:16 +05 2019
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: sun8iw12
[ 0.000000] cma: Reserved 384 MiB at 0x63c00000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] BUG: not creating mapping for 0x48105000 at 0x38105000 in user region
[ 0.000000] On node 0 totalpages: 262144
[ 0.000000] free_area_init_node: node 0, pgdat c0d20440, node_mem_map e0ff9000
[ 0.000000] Normal zone: 1072 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 137216 pages, LIFO batch:31
[ 0.000000] HighMem zone: 124928 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 13 pages/cpu @e0f76000 s22080 r8192 d22976 u53248
[ 0.000000] pcpu-alloc: s22080 r8192 d22976 u53248 alloc=13*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 261072
[ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x05000c00 initcall_debug=0 console=ttyS0,115200 loglevel=8 rootwait=1 root=/dev/mmcblk0p1 fsck.repair=yes init=/init partitions=boot-res@mmcblk0p2:env@mmcblk0p5:boot@mmcblk0p6:UDISK@mmcblk0p1 cma=384M vmalloc=480M mac_addr= wifi_mac= mix=0x1000@0x7bd31000 mbr=0x3e0
[ 0.000000] log_buf_len individual max cpu contribution: 4096 bytes
[ 0.000000] log_buf_len total cpu_extra contributions: 12288 bytes
[ 0.000000] log_buf_len min size: 16384 bytes
[ 0.000000] log_buf_len: 32768 bytes
[ 0.000000] early log buf free: 14608(89%)
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 632948K/1048576K available (7168K kernel code, 1198K rwdata, 2156K rodata, 1024K init, 230K bss, 22412K reserved, 393216K cma-reserved, 106492K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xe2000000 - 0xff800000 ( 472 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe1800000 ( 536 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0800000 (8160 kB)
[ 0.000000] .init : 0xc0b00000 - 0xc0c00000 (1024 kB)
[ 0.000000] .data : 0xc0c00000 - 0xc0d2bb94 (1199 kB)
[ 0.000000] .bss : 0xc0d2d000 - 0xc0d668d4 ( 231 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000020] Switching to timer-based delay loop, resolution 41ns
[ 0.000154] Console: colour dummy device 80x30
[ 0.000181] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.000198] pid_max: default: 32768 minimum: 301
[ 0.000437] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000452] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001254] CPU: Testing write buffer coherency: ok
[ 0.001311] ftrace: allocating 27419 entries in 81 pages
[ 0.044759] CPU0: update cpu_capacity 1024
[ 0.044780] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.044878] Setting up static identity map for 0x40100000 - 0x40100058
[ 0.124686] CPU1: update cpu_capacity 1024
[ 0.124692] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.154701] CPU2: update cpu_capacity 1024
[ 0.154708] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.184749] CPU3: update cpu_capacity 1024
[ 0.184755] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.184824] Brought up 4 CPUs
[ 0.184857] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 0.184865] CPU: All CPU(s) started in SVC mode.
[ 0.185693] devtmpfs: initialized
[ 0.235643] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.236246] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.236282] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.251474] atomic64_test: passed
[ 0.251504] pinctrl core: initialized pinctrl subsystem
[ 0.253025] NET: Registered protocol family 16
[ 0.254950] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.255664] dump_class_init,855, success
[ 0.258309] sun8iw12p1-r-pinctrl r_pio: initialized sunXi PIO driver
[ 0.262634] sun8iw12p1-pinctrl pio: initialized sunXi PIO driver
[ 0.264595] sunxi hwspinlock vbase:0xf3004000
[ 0.313059] pwm module init!
[ 0.319962] [ARISC] Confusedunxi-arisc driver v1.06
[ 0.321255] msgbox pbase:0x03003000, vbase:0xf3003000, size:0x1000, irq:0xdc, status:1
[ 0.321961] [ARISC] :hwmsgbox initialize
[ 0.324227] [ARISC] :arisc version: [sun8iw5_v0.03.00-399-g9fac845]
[ 0.324253] [ARISC] Confusedunxi-arisc driver v1.06 startup succeeded
[ 0.325366] SCSI subsystem initialized
[ 0.325902] usbcore: registered new interface driver usbfs
[ 0.326019] usbcore: registered new interface driver hub
[ 0.326179] usbcore: registered new device driver usb
[ 0.328958] media: Linux media interface: v0.10
[ 0.329072] Linux video capture interface: v2.00
[ 0.330151] Advanced Linux Sound Architecture Driver Initialized.
[ 0.331230] Bluetooth: Core ver 2.21
[ 0.331297] NET: Registered protocol family 31
[ 0.331307] Bluetooth: HCI device and connection manager initialized
[ 0.331327] Bluetooth: HCI socket layer initialized
[ 0.331345] Bluetooth: L2CAP socket layer initialized
[ 0.331396] Bluetooth: SCO socket layer initialized
[ 0.332713] of_property_read_u32_array ac200.tv_used fail
[ 0.333334] [axp233] chip id not detect 0x62 !
[ 0.333438] [axp233] enable dcdc2 dvm.
[ 0.345531] clocksource: Switched to clocksource arch_sys_counter
[ 0.408215] NET: Registered protocol family 2
[ 0.409056] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.409151] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.409267] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.409395] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.409451] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.409786] NET: Registered protocol family 1
[ 0.410218] RPC: Registered named UNIX socket transport module.
[ 0.410229] RPC: Registered udp transport module.
[ 0.410237] RPC: Registered tcp transport module.
[ 0.410244] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.416449] sunxi budget cooling probe start !
[ 0.416484] CPU freq cooling register Success
[ 0.416508] CPU hotplug cooling register Success
[ 0.416900] CPU budget cooling register Success
[ 0.417525] [DISP]disp_module_init
[ 0.417887] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.419618] spi spi1: master is unqueued, this is deprecated
[ 0.420252] [DISP] boot_disp:0x0
[ 0.433543] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.433953] Registering sdcardfs 0.1
[ 0.435332] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.436676] fuse init (API version 7.23)
[ 0.439041] NET: Registered protocol family 38
[ 0.439192] bounce: pool size: 64 pages
[ 0.439511] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 0.439537] io scheduler noop registered
[ 0.439554] io scheduler deadline registered
[ 0.439632] io scheduler cfq registered (default)
[ 0.455326] rotation_sw module is config as no used
[ 0.455362] [DISP] disp_get_rotation_sw,line:130:
[ 0.455370] disp 0 out of range? g_rot_sw=0
[ 0.455378] [DISP] disp_init_connections,line:385:
[ 0.455384] NULL pointer: 0, 0
[ 0.458298] [DISP] fb_base:0x46400000
[ 0.522382] format0,para:32bpp,a(24,8),r(16,8),g(8,8),b(0,8)
[ 0.525833] [DISP]disp_module_init finish
[ 0.525866] disp_module_init+0x0/0x124 complete comp.
[ 0.526679] np name = /soc@03000000/rtc@07000000
[ 0.526694] base = f7000100, len = 8.
[ 0.526755] pmu1 does not exist.
[ 0.527090] axp_add_sys_pwr_dm: get ldo name for id: vcc-lpddr failed
[ 0.527298] axp_add_sys_pwr_dm: vcc-pc not sys id.
[ 0.527307] after inited: sys_mask config = 0x4a55.
[ 0.527389] Warning: can not find np for dynamic_standby_para.
[ 0.527808] lookup_scene_lock_name: new scene lock super_standby
[ 0.527818] scene_lock_init name=super_standby
[ 0.527829] scene_lock: super_standby, type 5, count 1
[ 0.527837] enter set_extended_standby_manager
[ 0.527848] leave set_extended_standby_manager : id 0x8
[ 0.534138] uart0: ttyS0 at MMIO 0x5000000 (irq = 232, base_baud = 1500000) is a SUNXI
[ 0.534172] sw_console_setup()1271 - console setup baud 115200 parity n bits 8, flow n
[ 1.502477] console [ttyS0] enabled
[ 1.507501] uart1: ttyS1 at MMIO 0x5000400 (irq = 233, base_baud = 1500000) is a SUNXI
[ 1.517507] misc dump reg init
[ 1.522407] G2D: Module initialized.major:247
[ 1.528187] sunxi-wlan wlan: wlan_busnum (1)
[ 1.532959] sunxi-wlan wlan: wlan_usbnum (3)
[ 1.537756] sunxi-wlan wlan: wlan_power_name (vcc33-wifi)
[ 1.543789] sunxi-wlan wlan: io_regulator_name (vcc18-wifi)
[ 1.550069] sunxi-wlan wlan: wlan_regon gpio=356 mul-sel=1 pull=-1 drv_level=-1 data=0
[ 1.559343] sunxi-wlan wlan: get gpio wlan_en failed
[ 1.564902] sunxi-wlan wlan: wlan_hostwake gpio=357 mul-sel=6 pull=-1 drv_level=-1 data=0
[ 1.574463] sunxi-wlan wlan: get gpio wlan_clk_gpio failed
[ 1.580621] sunxi-wlan wlan: enable clk
[ 1.585646] sunxi-bt bt: bt_power_name (vcc18-wifi)
[ 1.591098] sunxi-bt bt: io_regulator_name (vcc-pg)
[ 1.596592] sunxi-bt bt: bt_rst gpio=364 mul-sel=1 pull=-1 drv_level=-1 data=0
[ 1.606078] tun: Universal TUN/TAP device driver, 1.6
[ 1.611720] tun: © 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.620102] gmac-power1: NULL
[ 1.623417] gmac-power2: NULL
[ 1.628417] PPP generic driver version 2.4.2
[ 1.633528] PPP BSD Compression module registered
[ 1.638819] PPP Deflate Compression module registered
[ 1.644474] PPP MPPE Compression module registered
[ 1.649852] NET: Registered protocol family 24
[ 1.654855] PPTP driver version 0.8.5
[ 1.659406] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.667026] get ehci0-controller, regulator_io is no nocare
[ 1.673380] [sunxi-ehci0]: probe, pdev->name: 5101000.ehci0-controller, sunxi_ehci: 0xc0d54e9c, 0x:f5101000, irq_no:ee
[ 1.685411] sunxi-ehci 5101000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.695573] sunxi-ehci 5101000.ehci0-controller: new USB bus registered, assigned bus number 1
[ 1.705589] sunxi-ehci 5101000.ehci0-controller: irq 238, io mem 0xc04b1328
[ 1.725561] sunxi-ehci 5101000.ehci0-controller: USB 0.0 started, EHCI 1.00
[ 1.734646] hub 1-0:1.0: USB hub found
[ 1.738901] hub 1-0:1.0: 1 port detected
[ 1.743913] [ehci0-controller]: sunxi_usb_disable_ehci
[ 1.749683] [sunxi-ehci0]: remove, pdev->name: 5101000.ehci0-controller, sunxi_ehci: 0xc0d54e9c
[ 1.759435] sunxi-ehci 5101000.ehci0-controller: remove, state 1
[ 1.766181] usb usb1: USB disconnect, device number 1
[ 1.773441] sunxi-ehci 5101000.ehci0-controller: USB bus 1 deregistered
[ 1.781152] get ehci1-controller, regulator_io is no nocare
[ 1.787563] [sunxi-ehci1]: probe, pdev->name: 5200000.ehci1-controller, sunxi_ehci: 0xc0d55040, 0x:f5200000, irq_no:f0
[

... at this moment the device itself is reset and rebooted. the log starts to be displayed from the beginning.
Reply
#4
I connect lindenis board to usb3.0 (up to 2A) and the linux image is fully loaded!!!
Reply
#5
great tutorial, thanks for sharing !
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)